Quanmax KEMF-4010 Betriebsanweisung

I KEMF-4010 User’s KEMF-4010 FlexATX Embedded Motherboard with AMD Athlon™ Single and Dual-Core Processors and AMD® 780E + SB710

Preface 10 KEMF-4010 User’s Preface  How to Use This Guide This guide is designed to be used as step-by-step instructions for installation, and as a

Preface 11 KEMF-4010 User’s their own expense. Changes or modifications not expressly approved by Quanmax could void the user's authority to oper

Preface 12 KEMF-4010 User’s and building replacement products. If Quanmax repairs or replaces a product, its warranty term is not extended. Shipments

Preface 13 KEMF-4010 User’s  Altitude Operating a system at a high altitude (low pressure) reduces the efficiency of the cooling fans to cool the sy

Chapter 1 14 KEMF-4010 User’s Chapter 1 Introduction  Overview The KEMF-4010 is a FlexATX embedded motherboard that built with the fastest onboa

Chapter 1 15 KEMF-4010 User’s  Product Specifications CPU Support AMD Athlon™ Single and Dual-Core Processors Chipset AMD780E + SB710 Memory 2x

Chapter 1 16 KEMF-4010 User’s  System Block Diagram Figure 1 Block Diagram

Chapter 1 17 KEMF-4010 User’s  Mechanical Dimensions Figure 2 KEMF-4010 Mechanical Dimensions

Chapter 2 18 KEMF-4010 User’s Chapter 2 Hardware Settings  Overview This chapter provides the definitions and locations of jumpers, headers, and c

Chapter 2 19 KEMF-4010 User’s  Jumper Settings and Pin Definitions For jumper and connector locations, please refer to the diagrams below. Figure 4

II KEMF-4010 User’s Contact Info: Quanmax Inc. 5F, No. 415, Ti-Ding Blvd. Sec. 2, NeiHu District, Taipei, Taiwan 114 Tel: +886-2-2799-2789 Fa

Chapter 2 20 KEMF-4010 User’s Jumper Settings To ensure correct system configuration, the following section describes how to set the jumpers to enable

Chapter 2 21 KEMF-4010 User’s Table 5 JP5, Parallel Port Signal Selection Jumper Setting Function 1 1-2 Short Pin 4 of LPT1 = ERR# (Default) 1-3

Chapter 2 22 KEMF-4010 User’s Table 10 JP14, KB / MS Signal Selection Pin Signal Name Pin Signal Name 1 +5V 2 GND 3 KBCLK from SIO 4 KBDAT from

Chapter 2 23 KEMF-4010 User’s Table 14 VGA_COM1, RS-232 / 422 / 485 Port 1 DB15+DB9 Connector Pin Signal Name Pin Signal Name V1 Red V2 Green V3 Blu

Chapter 2 24 KEMF-4010 User’s Table 17 PS2-KBMS1, PS/2 KB/MS Mini-DIN Connector Pin Signal Function 1 KBDAT Keyboard Data 2 NC No Connect 3 GND Gr

Chapter 2 25 KEMF-4010 User’s Main Board Pin Assignments Table 19 Internal Connector List Label Function Label Function ATXPWR1 24-pin ATX Power I

Chapter 2 26 KEMF-4010 User’s Table 21 ATX12V1, 4-pin ATX Power Input Connector Pin Signal Pin Signal 1 GND 2 GND 3 +12V 4 +12V Pitch:4.2mm 空心 PI

Chapter 2 27 KEMF-4010 User’s Table 24 DIO1, Digital Input / Output Pin Header Pin Signal Pin Signal 1 Digital Output 0 2 Digital Input 0 3 Di

Chapter 2 28 KEMF-4010 User’s Table 29 CPU_FAN1, FAN Wafer Pin Signal 1 GND 2 +12V 3 FAN_RPM 4 FAN_RPM_CTL Pitch: 2.54mm WAFER [FOXCONN HF2704E-M1]

Chapter 2 29 KEMF-4010 User’s Table 33 LVDS1, LVDS Panel Connector Signal Name Pin Pin Signal Name NC 2 1 NC +3.3V / +5V* 4 3 +3.3V / +5V* Txclk

Content 3 KEMF-4010 User’s Content 0HContent ...

Chapter 2 30 KEMF-4010 User’s 11 Reserved IDSEL1 * 12 Ground Ground 13 Ground Ground 14 CLK1 * +3.3VAUX 15 Ground RST# 16 CLK0 +5V17 Ground GNT0# 18

Chapter 2 31 KEMF-4010 User’s Table 36 PCIE1, Standard PCI Express x16 Slot Pin Side B Side A 1 +12V PRSNT#(B) 2 +12V +12V 3 +12V +12V 4 Ground Groun

Chapter 2 32 KEMF-4010 User’s 62 HSOP11 Ground 63 HSON11 Ground 64 Ground HSIP11 65 Ground HSIP11 66 HSOP12 Ground 67 HSON12 Ground 68 Ground HSIP12 6

Chapter 2 33 KEMF-4010 User’s Table 39 PCIE2, PCIE3, Standard PCI Express x1 Slot Pin Side B Side A 1 +12V +3.3V 2 +12V +3.3V 3 +3.3VAUX Ground

Chapter 2 34 KEMF-4010 User’s Table 41 MPCIE1, Mini PCIe Connector Signal Pin Pin Signal WAKE# 1 2 +3.3V Reserved 3 4 Ground Reserved 5 6 +1.

Chapter 3 35 KEMF-4010 User’s Chapter 3 System Installation  Processor Installation Processor Handling Carefully follow the steps below in order t

Chapter 3 36 KEMF-4010 User’s 4. Make sure that the CPU pins fit perfectly into their holes. Once the CPU is positioned into its socket, place one fi

Chapter 3 37 KEMF-4010 User’s  Cooler Installation The system must not be operated without a cooler (heat sink and fan) to provide the necessarily c

Chapter 3 38 KEMF-4010 User’s 5. Turn the cam handle from the left side to the right side to lock into place. (Refer to your CPU cooler installation

Chapter 3 39 KEMF-4010 User’s Figure 11 DIMM Memory and 240-pin Socket Installing a DIMM Carefully follow the steps below in order to install the DIM

Content 4 KEMF-4010 User’s Chapter 4 AMI BIOS Setup ... 41 　 Overvi

Chapter 3 40 KEMF-4010 User’s Removing a DIMM: To remove the DIMM, use your fingers or a small screwdriver to carefully push away the plastic tabs tha

Chapter 4 41 KEMF-4010 User’s Chapter 4 AMI BIOS Setup  Overview This chapter provides a description of the AMI BIOS. The BIOS setup menus and av

Chapter 4 42 KEMF-4010 User’s  Main Menu The BIOS Setup is accessed by pressing the DEL key after the Power-On Self-Test (POST) memory test begins a

Chapter 4 43 KEMF-4010 User’s not previously formatted with LBA mode disabled. Options: Disabled, Auto DMA Mode [Auto] Setup DMA Mode. S.M.A.R.T [Au

Chapter 4 44 KEMF-4010 User’s booting to decrease the time needed to boot the system. When set to [Disabled], BIOS performs all the POST items. Option

Chapter 4 45 KEMF-4010 User’s Table 47 OnBoard Peripherals Configuration Settings BIOS SETUP UTILITY Main Advanced Boot Chipset Power

Chapter 4 46 KEMF-4010 User’s OnChip SATA Channel [Enabled] Options: Enabled, Disabled OnChip SATA Type [IDE] Options: IDE, RAID, AHCI Table 49 Onboa

Chapter 4 47 KEMF-4010 User’s Options: Normal, IrDA, ASK IR COM6 Address [220] Options: Disabled, 3F8, 2F8, 3E8, 2E8, 228 220 COM6 IRQ [7] Options: 3,

Chapter 4 48 KEMF-4010 User’s CPU Warning Temperature Options: Disabled, 80°C/176°F, 85°C/185°F, 90°C/194°F, 95°C/203°F CPU Shutdown Temperature Optio

Chapter 4 49 KEMF-4010 User’s LVDS1 Port Type [LVDS 24bit] Options: DVI, LVDS 24bit, LVDS 18bit Video Display Devices [Auto] Options: Auto, VGA, LVDS,

Figures 5 KEMF-4010 User’s Figures Figure 1 Block Diagram ...

Chapter 4 50 KEMF-4010 User’s  Power Menu Table 55 Power Menu BIOS SETUP UTILITY Main Advanced Boot Chipset Power Security E

Chapter 4 51 KEMF-4010 User’s Resume From S3 By USB Device [Disabled] Options: Disabled, Enabled Resume by PCI Device (PME#) [Disabled] Options: Disab

Chapter 4 52 KEMF-4010 User’s  Exit Menu Table 58 Exit Menu BIOS SETUP UTILITY Main Advanced Boot Chipset Power Security Exi

Chapter 5 53 KEMF-4010 User’s Chapter 5 Driver Installation If your KEMF-4010 does not come with an operating system pre-installed, you will need to

Appendix A 54 KEMF-4010 User’s Appendix A DIO (Digital I/O) Programming Guide I/O Port CF8~B: Address Port (32bit) I/O Port CFC~F: Data Port (32bit)

Appendix B 55 KEMF-4010 User’s Appendix B WatchDog Timer Sample Code //============================================ //KEMF-4010 DOS watchdog sample pr

Tables 6 KEMF-4010 User’s Tables Table 1 KEMF-4010 Specification ... 15 Table 2 Jumper List ...

Tables 7 KEMF-4010 User’s Table 35 PCI1, 32-bit / 33Mhz / 5V-key PCI Slot ... 29 Table 36 PCIE1, Standard PCI Express x16 Slot ..

Safety Instructions 8 KEMF-4010 User’s Safety Instructions  Before You Begin Before handling the product, read the instructions and safety guideline

Safety Instructions 9 KEMF-4010 User’s  To help avoid possible damage to system boards, wait five seconds after turning off the computer before remo